This view of the Owner’s Manual contains the very latest information, which may vary slightly from the printed Owner’s Manual originally provided with your vehicle. It may also describe content that is not on or operates differently on your vehicle. Please consider the Owner’s Manual originally provided with your vehicle as the primary source of information for your vehicle.
The information contained in this publication was correct at the time of release.In the interest of continuous development, we reserve the right to change specifications, design or equipment at any time without notice or obligation.No part of this publication may be reproduced, transmitted, stored in a retrieval system or translated into any language in any form by any means without our written permission.Errors and omissions excepted.
Copyright © 2024 Ford Motor Company
Keyless Entry
You can use the keypad to:
SECURICODE™ KEYLESS ENTRY KEYPAD
The keypad is located near the driver window. It is invisible until touched and then it lights up so you can see and touch the appropriate buttons.
Note:
If you enter your entry code too fast on the keypad, the unlock function may not work. Re-enter your entry code more slowly.
You can use the keypad to:- lock or unlock the doors
- recall memory seat and mirror positions
- program and erase personal entry codes
- arm and disarm the anti-theft alarm
- release the trunk.
Note:
The keypad will not operate a power decklid.
You can operate the keypad with the factory-set 5-digit entry code. The code is located on the owner’s wallet card in the glove box and is available from an authorized dealer. You can also create up to five of your own 5-digit personal entry codes.
Programming a Personal Entry Code
To create your own personal entry code:
- Enter the factory-set code.
- Press 1·2 on the keypad within five seconds.
- Enter your personal 5-digit code. You must enter each number within five seconds of each other.
- Press 1·2 on the keypad to save personal code 1.
The doors will lock then unlock to confirm that programming was successful.
To program additional personal entry codes, repeat Steps 1-3, then for Step 4:
- press 3·4 to save personal code 2
- press 5·6 to save personal code 3
- press 7·8 to save personal code 4
- press 9·0 to save personal code 5.
You may also program a personal entry code using the touchscreen. See
Settings.
Tips:- Do not set a code that uses five of the same number.
- Do not use five numbers in sequential order.
- The factory-set code will work even if you have set your own personal code.
Recalling Memory Positions
The programmed entry codes will recall driver memory positions as follows:
- Entry code 1 will recall driver 1 memory positions.
- Entry code 2 will recall driver 2 memory positions.
- Entry code 3 will recall driver 3 memory positions.
Note:
Personal entry codes 4 and 5 will not recall memory positions.
Erasing a Personal Code
- Enter the factory-set 5-digit code.
- Press and release 1·2 on the keypad within five seconds.
- Press and hold 1·2 for two seconds. You must do this within five seconds of completing Step 2.
All personal codes are now erased and only the factory-set 5–digit code will work.
Anti-Scan Feature
The keypad will go into an anti-scan mode if you enter the wrong code seven times (35 consecutive button presses). This mode disables the keypad for one minute and the keypad lamp will flash.
The anti-scan feature will turn off after:- one minute of keypad inactivity
- pressing the unlock button on the remote control
- switching the ignition on
- unlocking your vehicle using intelligent access.
Unlocking and Locking the Doors
To Unlock the Driver Door
Enter the factory-set 5-digit code or your personal code. You must press each number within five seconds of each other. The interior lamps will illuminate.
Note:
All doors will unlock if you enable the all-door unlocking mode. See
Locking and Unlocking.
To Unlock All Doors
Enter the factory-set code or your personal code, then press 3·4 within five seconds.
To Lock All Doors
Press and hold 7·8 and 9·0 at the same time (with the driver door closed). You do not need to enter the keypad code first.
To Release the Trunk
Enter the factory-set code or your personal code, then press 5·6 within five seconds.
Note:
The keypad will not operate a power decklid.
Displaying the Factory Set Code
Note:
You will need to have two programmed intelligent access keys for this procedure.
To display the factory-set code in the information display:
- Remove the rubber covering (A) in the cupholder. Place the first programmed key in the backup slot (B) at the bottom of the cupholder.
- Press the START/STOP button once and wait a few seconds.
- Press the START/STOP button again and remove the key.
- Insert the second programmed key into the backup slot, then press the START/STOP button.
The factory-set code will appear in the information display for a few seconds.
Note:
The code may not display until after any other warning messages first display.